This revision permits the publication of BS EN to be adopted as a Harmonised Standard under the Constuction Products Directive. BS EN. Hot finished structural hollow sections of non-alloy and fine grain steels -. Part 1: Technical delivery conditions d Copy. Find the most up-to-date version of BS EN at Engineering

Author: Mujind Kisho
Country: Pacific Islands
Language: English (Spanish)
Genre: Software
Published (Last): 5 May 2010
Pages: 432
PDF File Size: 13.18 Mb
ePub File Size: 2.19 Mb
ISBN: 949-8-67441-338-8
Downloads: 61309
Price: Free* [*Free Regsitration Required]
Uploader: Ferg

For undated references, the latest edition of the referenced document including any amendments applies. NOTE Cold formed hollow sections with subsequent heat treatment to obtain properties equivalent to those obtained by normalizing rolling are deemed to meet the requirements of this standard.

Otherwise, the NPD option may be used when and where the characteristic, for a given intended use, is not subject to regulatory requirements in the Member State of destination. These will vary depending on the product thickness, the applied welding energy, the design requirements, the electrode efficiency, the welding process and the weld metal properties.

BS EN 10210-1:2006

In accordance with the classification system in ENall steel grades in Annex A are non-alloy quality steels. In case of dispute, the method used shall be agreed taking into account CR Find Similar Items This product falls into the following categories. B — Description of products to which the test report applies. The minimum average values given in Table A.

BS EN for Hot Finished Structural Hollow Sections

EN and EN 6. Longitudinal or transverse samples at the discretion of the manufacturer. If these details are bx be used for any other purpose than implementation then the prior written permission of BSI 100210-1 be obtained. The minimum frequency of testing shall be in accordance with Table D. NOTE 2 By using guidelines, specified for example in ENEN or any other relevant standard, the recommended welding conditions and the various welding ranges for the steel grades can be determined.

Compliance with a British Standard does not of itself confer immunity from legal obligations. The Amber document status indicator indicates that some caution is needed when using this document – it is ej The conditions under which, and the extent to which, welding repair to fn body may be carried out shall be agreed between the manufacturer and the purchaser. Identification number of the notified body;? Annex ZA 10210-11 this European Standard ;? BSI also holds the copyright, in the UK, of the publications of the international standardization bodies.


Warmgefertigte Hohlprofile fuer den Bbs aus unlegierten Baustaehlen und aus Feinkornbaustaehlen. Users are responsible for its correct application. General guidance for arc welding ENWelding — Recommendations for welding of metallic materials — Part 2: In cases where this would mean assessment of steel hollow sections for which type testing in accordance with this standard had already been performed, the testing frequency may be reduced: In addition, the general technical delivery requirements specified in EN shall apply.

C — Information on tests as follows: The decision shall be left to the discretion of the manufacturer, but shall be stated to the purchaser at the time of enquiry and order.

Technical delivery requirements Withdrawn. Tolerances, dimensions and sectional properties It forms part of a series of standards on hollow sections together with EN and 2, which are also under revision.

In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.

We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the 110210-1 of which can be found on the inside front cover.

Accept and continue Learn more about 10210–1 cookies we use and how to change your settings. This declaration shall include: The choice of a suitable physical or chemical analytical method for the analysis shall be at the discretion of 10120-1 manufacturer. If the nominal product thickness is not sufficient for the preparation of standard test pieces, the test shall be carried out using test pieces of width less than 10 mm, but not less than 5 mm.


Tables are in Annexes A and B, formula for calculation is specified.

SJ2H structural hollow section according to EN – SSAB

The scope of this annex is defined by Table ZA. Automatic eddy current testing of seamless and welded except submerged arc-welded steel tubes for the detection of imperfections ENNon-destructive testing of steel tubes — Part 5: NOTE Test piece size is dependent on the actual thickness of the sample and, for circular or elliptical hollow sections; allowance also needs to be made for the curvature of the section.

Except as permitted under the Copyright, Designs and Patents Act no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means rn electronic, photocopying, recording or otherwise — without prior written permission from BSI. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 38, an inside back cover and a back cover.

NOTE 1 In addition to any specific clauses relating to dangerous substances contained in this standard, there may be other requirements applicable to the products falling within its scope e. Technical delivery requirements Status: It shall also be agreed which party shall issue the certificate. The following samples shall be taken from one sample product of each test unit: The performance characteristics and the means ne verification are: Various BSI electronic information services are also available which give 1010-1 on all its products and services.

BS EN Worldwide Standards We can source any standard from anywhere in the world. Click here to find out how to access this document. Standards are also available from the BSI website at http: